收藏本站
CAT4004
Table 5. PIN DESCRIPTIONS
Pin #
1
2
3
4
5
6
7
8
TAB
Name
EN/DIM
GND
LED1
LED2
LED3
LED4
RSET
VIN
TAB
Device enable (active high) and dimming control
Ground reference
LED1 cathode terminal
LED2 cathode terminal
LED3 cathode terminal
LED4 cathode terminal
RSET external LED mirror gain 128
Device supply input, connect to battery or supply
Connect to GND on the PCB
Function
Pin Function
VIN is the supply pin for the device logic. A small 1 m F
ceramic bypass capacitor is required between the VIN pin
and ground near the device. The operating input voltage
range is from 2.5 V to 5.5 V. Whenever the input supply falls
below the under ? voltage threshold (1.8 V), all the LED
channels are disabled and the device enters shutdown mode.
EN/DIM is the enable and one wire dimming input for all
LED channels. Levels of logic high and logic low are set at
1.3 V and 0.4 V respectively. When EN/DIM is initially
taken high, the device becomes enabled and all LED
currents are set to the full scale according to the resistor
R SET . To place the device into “zero current” shutdown
mode, the EN/DIM pin must be held low for at least 1.5 ms.
impedance zero current state whenver the device is placed
in shutdown mode.
RSET is connected to the resistor (R SET ) to set the full scale
current for the LEDs. The voltage at this pin is regulated to
0.6 V. The ground side of the external resistor should be star
connected back to the GND of the PCB. In shutdown mode,
RSET beomes high impedance.
GND is the ground reference for the device. The pin must be
connected to the ground plane on the PCB.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
LED1 to LED4 provide the internal regulated current for
each of the LED cathodes. There pins enter a high
http://onsemi.com
7
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CAT4008W-T2 IC LED DRIVER LINEAR 16-SOIC
CAT4101TV-T75 IC LED DRVR HP CONST CURR D2PAK
CAT4104V-GT3 IC LED DVR 4CH 175MA 8SOIC
CAT4106YP-T2 IC LED DVR 4CH BOOST 16TSSOP
CAT4109V-GT2 IC LED DRIVER RGB 16-SOIC
CAT4134HV2-T2 IC LED DRVR BKLGHT FLASH 12-TDFN
CAT4137TD-T3 IC LED DRVR WHITE BCKLGHT TSOT-5
CAT4139TD-GT3 IC LED DRVR WHITE BCKLGT TSOT-5
相关代理商/技术参数
CAT4008 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:8-Channel Constant Current LED Driver
CAT4008V-T1 功能描述:LED照明驱动器 LED Driver 8 Chan 4-wire I/F RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
CAT4008W-T2 功能描述:LED照明驱动器 8-Ch Linear 4-Wire RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
CAT4008Y 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT4008Y-GT2 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:8-Channel Constant Current LED Driver
CAT4008Y-T2 功能描述:LED照明驱动器 LED Driver 8 Chan 4-wire I/F RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
CAT4016 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:16-Channel Constant Current LED Driver
CAT4016_08 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:16-Channel Constant Current LED Driver